Подключен к провайдеру по технологии Ethernet. Настройки получаю по DHCP. Постоянно виснет WAN порт. Раза 3 в день стабильно. Причем виснет даже когда все от роутера отключено и никакой нагрузки на него нет.
прошивка 1.0.14. При передергивании патчкорда связюка появляеться.
Завис он в промежутка между вот этими двумя событиями из лога
Код:
Jan 15 23:08:52 kernel: dlink: emfc_mfdb_membership_add: mgrp_ip is zero, stack:
Jan 16 07:03:42 resident: getting wan port status
Смущает что с какого-то момента в логе не происходит " resident: getting wan port status". Я так понимаю опрашивается состояние порта.
Вот полный лог:
Код:
Jan 1 00:00:12 resident: start ipoe
Jan 1 00:00:12 start_ip: begin (br0 -> br0)
Jan 1 00:00:12 resident: start ipoe (v2142194328) on br0
Jan 1 00:00:13 resident: init wan
Jan 1 00:00:13 resident: start ipoe
Jan 1 00:00:13 start_ip: begin (wan1 -> wan1_1)
Jan 1 00:00:13 resident: start ipoe (v2) on wan1
Jan 1 00:00:13 update_ddns: start
Jan 1 00:00:13 telnet-start: begin...
Jan 1 00:00:13 telnet-start: running on 23 port
Jan 1 00:00:13 telnet-start: succes!
Jan 1 00:00:13 resident: Out init_device
Jan 1 00:00:13 resident: record = action:up;iface:br0;contag:0;ipaddr:192.168.1.1;netmask:255.255.255.0;dns1:;dns2:;
Jan 1 00:00:13 resident: phys_iface br0
Jan 1 00:00:13 test: ip_type = (null)
Jan 1 00:00:13 resident: resident_ipoe_handler - Set default type: ipv4
Jan 1 00:00:13 resident: phys_iface
Jan 1 00:00:13 resident: resident_ipoe_handler - 1
Jan 1 00:00:13 resident: resident_ipoe_handler - 3, name: br0
Jan 1 00:00:13 event: send event "ipoe down"
Jan 1 00:00:13 resident: resident_ipoe_handler - l2:br0, l3:br0, tun:, ip_type:0
Jan 1 00:00:13 resident: resident_ipoe_handler - ipv4
Jan 1 00:00:13 resident: start ip_is_up on iface br0
Jan 1 00:00:13 resident: ip_is_up for link br0
Jan 1 00:00:13 resident: start dhcp+dns on br0
Jan 1 00:00:13 upnp: start - begin
Jan 1 00:00:13 upnp: upnp disable - exit
Jan 1 00:00:14 resident: record = action:down;iface:wan1;contag:1;
Jan 1 00:00:14 resident: phys_iface wan1
Jan 1 00:00:14 test: ip_type = (null)
Jan 1 00:00:14 resident: resident_ipoe_handler - Set default type: ipv4
Jan 1 00:00:14 resident: phys_iface
Jan 1 00:00:14 resident: resident_ipoe_handler - 2
Jan 1 00:00:14 resident: resident_ipoe_handler - 3, name: wan1_1
Jan 1 00:00:14 resident: resident_ipoe_handler - l2:wan1, l3:wan1_1, tun:, ip_type:0
Jan 1 00:00:14 resident: ip_is_down on wan1_1
Jan 1 00:00:15 event: send event "ipoe up"
Jan 1 00:00:15 resident: record = action:up;iface:wan1;contag:1;ipaddr:62.68.132.172 ;netmask:255.255.254.0 ;gateway:62.68.132.1 ;dns1:77.106.108.139;dns2:77.106.109.139;
Jan 1 00:00:15 resident: phys_iface wan1
Jan 1 00:00:15 test: ip_type = (null)
Jan 1 00:00:15 resident: resident_ipoe_handler - Set default type: ipv4
Jan 1 00:00:15 resident: phys_iface
Jan 1 00:00:15 resident: resident_ipoe_handler - 2
Jan 1 00:00:15 resident: resident_ipoe_handler - 3, name: wan1_1
Jan 1 00:00:15 resident: resident_ipoe_handler - l2:wan1, l3:wan1_1, tun:, ip_type:0
Jan 1 00:00:15 resident: resident_ipoe_handler - ipv4
Jan 1 00:00:15 resident: start ip_is_up on iface wan1_1
Jan 1 00:00:15 resident: ip_is_up for link wan1_1
Jan 1 00:00:15 set_dhcp_routes: set routes for iface wan1
Jan 1 00:00:15 resident: update dns
Jan 1 00:00:15 resident: update rip
Jan 1 00:00:15 resident: update igmpx
Jan 1 00:00:15 resident: stop igmpx
Jan 1 00:00:15 iface: this is wan1
Jan 1 00:00:15 resident: igmpx wan1
Jan 1 00:00:15 resident: update igmpx compiled
Jan 1 00:00:15 resident: update ntpclient
Jan 15 22:18:11 event: send event "ipoe lease fail"
Jan 15 22:18:11 resident: record = action:leasefail;iface:wan1;contag:1;
Jan 15 22:18:11 resident: phys_iface wan1
Jan 15 22:18:11 test: ip_type = (null)
Jan 15 22:18:11 resident: resident_ipoe_handler - Set default type: ipv4
Jan 15 22:18:11 resident: phys_iface
Jan 15 22:18:11 resident: resident_ipoe_handler - 2
Jan 15 22:18:11 resident: resident_ipoe_handler - 3, name: wan1_1
Jan 15 22:18:11 resident: resident_ipoe_handler - l2:wan1, l3:wan1_1, tun:, ip_type:0
Jan 15 22:18:11 resident: ip_is_down on wan1_1
Jan 15 22:18:11 event: send event "ipoe up"
Jan 15 22:18:11 resident: record = action:up;iface:wan1;contag:1;ipaddr:62.68.132.172 ;netmask:255.255.254.0 ;gateway:62.68.132.1 ;dns1:77.106.108.139;dns2:77.106.109.139;
Jan 15 22:18:11 resident: phys_iface wan1
Jan 15 22:18:11 test: ip_type = (null)
Jan 15 22:18:11 resident: resident_ipoe_handler - Set default type: ipv4
Jan 15 22:18:11 resident: phys_iface
Jan 15 22:18:11 resident: resident_ipoe_handler - 2
Jan 15 22:18:11 resident: resident_ipoe_handler - 3, name: wan1_1
Jan 15 22:18:11 resident: resident_ipoe_handler - l2:wan1, l3:wan1_1, tun:, ip_type:0
Jan 15 22:18:11 resident: resident_ipoe_handler - ipv4
Jan 15 22:18:11 resident: start ip_is_up on iface wan1_1
Jan 15 22:18:11 resident: ip_is_up for link wan1_1
Jan 15 22:18:11 set_dhcp_routes: set routes for iface wan1
Jan 15 22:18:11 resident: update dns
Jan 15 22:18:11 resident: update rip
Jan 15 22:18:11 resident: update igmpx
Jan 15 22:18:11 resident: stop igmpx
Jan 15 22:18:11 iface: this is wan1
Jan 15 22:18:11 resident: igmpx wan1
Jan 15 22:18:11 syslog: IGMP: checksum: expected 0x8a77, got 0xdcd8. Skip. (IP PROTO = 17)
Jan 15 22:18:11 resident: update igmpx compiled
Jan 15 22:18:11 resident: update ntpclient
Jan 15 22:20:29 resident: getting wan port status
Jan 15 22:27:01 kernel: dlink: emfc_mfdb_membership_add: mgrp_ip is zero, stack:
Jan 15 22:27:01 kernel: dlink: emfc_mfdb_membership_add: mgrp_ip is zero, stack:
Jan 15 22:54:26 resident: getting wan port status
Jan 15 22:54:29 resident: getting wan port status
Jan 15 23:08:52 kernel: dlink: emfc_mfdb_membership_add: mgrp_ip is zero, stack:
Jan 15 23:08:52 kernel: dlink: emfc_mfdb_membership_add: mgrp_ip is zero, stack:
Jan 16 07:03:42 resident: getting wan port status
Jan 16 07:05:15 resident: stop ipoe on wan1_1
Jan 16 07:05:15 resident: set lock /var/lock/wan1_1.lock
Jan 16 07:05:15 event: file "/var/lock/wan1_1.lock" is set
Jan 16 07:05:15 event: udhcp_down fake
Jan 16 07:05:16 resident: stop ipoe on wan1_1
Jan 16 07:05:16 resident: set lock /var/lock/wan1_1.lock
Jan 16 07:05:17 resident: start ipoe
Jan 16 07:05:17 start_ip: begin (wan1 -> wan1_1)
Jan 16 07:05:17 resident: start ipoe (v1024) on wan1
Jan 16 07:05:17 event: file "/var/lock/wan1_1.lock" is set
Jan 16 07:05:17 event: udhcp_down fake
Jan 16 07:05:18 event: send event "ipoe up"
Jan 16 07:05:18 resident: record = action:up;iface:wan1;contag:1;ipaddr:62.68.132.172 ;netmask:255.255.254.0 ;gateway:62.68.132.1 ;dns1:77.106.108.139;dns2:77.106.109.139;
Jan 16 07:05:18 resident: phys_iface wan1
Jan 16 07:05:18 test: ip_type = (null)
Jan 16 07:05:18 resident: resident_ipoe_handler - Set default type: ipv4
Jan 16 07:05:18 resident: phys_iface
Jan 16 07:05:18 resident: resident_ipoe_handler - 2
Jan 16 07:05:18 resident: resident_ipoe_handler - 3, name: wan1_1
Jan 16 07:05:18 resident: resident_ipoe_handler - l2:wan1, l3:wan1_1, tun:, ip_type:0
Jan 16 07:05:18 resident: resident_ipoe_handler - ipv4
Jan 16 07:05:18 resident: start ip_is_up on iface wan1_1
Jan 16 07:05:18 resident: ip_is_up for link wan1_1
Jan 16 07:05:18 set_dhcp_routes: set routes for iface wan1
Jan 16 07:05:18 resident: update dns
Jan 16 07:05:18 resident: update rip
Jan 16 07:05:18 resident: update igmpx
Jan 16 07:05:18 resident: stop igmpx
Jan 16 07:05:18 iface: this is wan1
Jan 16 07:05:18 resident: igmpx wan1
Jan 16 07:05:18 resident: update igmpx compiled
Jan 16 07:05:18 resident: update ntpclient
Jan 16 09:02:17 resident: getting wan port status
Jan 16 09:55:38 syslog: sendto: 3e4484ac -> effffffa: 1(Operation not permitted)
Jan 16 10:50:25 resident: getting wan port status
Как это можно пролечить. Пробовал прошивки разных версий. И еще получается что этот роутер не может работать в режиме бридж/клиент бридж и т.д.?
Вход
Регистрация
FAQ
Поиск
