Здравствуйте. Суть пролемы в следующем: на объекте стоит атс LG SOHO, трехзначная внутренняя нумерация, выход через в город через девятку, подключение телефонов в других зданиях осуществляется через DVG-6008S, DVG-5008s и DVG-G5402SP. И на устройстве g5402sp возникла проблема выхода в город - при наборе номера если на другой стороне не берут телефон линия удерживается и не возможно повтороно набрать номер. Только через определённое время. Как это устранить?

ВЫложите логи со шлюзов (5402 и 5008).

_________________
логи можно снять
[url]http://ftp.dlink.ru/pub/VoIP/DVG-6004S/Firmware/slmon(1225112422).rar[/url]

лог с 5008

13:44:53 *** SLMON start to log ***
13:45:03 [12053358] Receive Cmd=1100, ParaLen=0, Para=[]
13:45:03 [12053358] == Ver(1.02.37.61.8258 2008/02/20 08:19:47) PId(242.DLink.NoPrefix.drtp.vlan) Drv(0.9.5.1.735 29/Nov/2007 10:30:08) Hw(SA7S8) == 0.6.7-1
13:45:05 [12053383] 6: Fxs Pickup
13:45:05 [12053383] 6: HotLineEnabled with [607]
13:45:05 [12053383] 6: End Input Default Route [0]
13:45:06 [12053383] 6: OutPinCode=<>, dial_no=<607>
13:45:06 [12053384] 6: PhoneBook has GwNo=607, addr=10.0.0.1:5060
13:45:06 [12053384] 6: ==7:Inviting
13:45:06 [12053384] 6: VoIP CallOut, Invite <sip:607@10.0.0.1:5060;user=phone>
13:45:06 [12053385] 6: 707=DIALING
13:45:06 [12053386] 6: 707=PROCEEDING
13:45:06 [12053388] 6: 707=CONNECTED
13:45:06 [12053388] 6: Peer=10.0.0.1:9012, PT=18, RecvOnly=0
13:45:06 [12053388] 6: RtpApiTalk[1,1], Peer=10.0.0.1:9012, PT=18, FC=2, NewOOB=0
13:45:06 [12053388] 6: ==14:Talking
13:45:19 [12053522] DSP_ch6_check=0
13:45:19 [12053522] 6: Fxs Hangup
13:45:19 [12053522] 6: Bye at Talking
13:45:19 [12053523] 6: ==3:Idle
13:45:19 [12053523] 6: SetFax(1)=0
13:45:20 [12053524] 6: 707=DISCONNECT
13:45:20 [12053524] 6: Release Old Dlg #2
13:45:32 [12053644] 6: Fxs Pickup
13:45:32 [12053644] 6: HotLineEnabled with [607]
13:45:32 [12053644] 6: End Input Default Route [0]
13:45:32 [12053644] 6: OutPinCode=<>, dial_no=<607>
13:45:32 [12053644] 6: PhoneBook has GwNo=607, addr=10.0.0.1:5060
13:45:32 [12053644] 6: ==7:Inviting
13:45:32 [12053644] 6: VoIP CallOut, Invite <sip:607@10.0.0.1:5060;user=phone>
13:45:32 [12053645] 6: 707=DIALING
13:45:32 [12053646] 6: 707=PROCEEDING
13:45:32 [12053649] 6: 707=CONNECTED
13:45:32 [12053649] 6: Peer=10.0.0.1:9012, PT=18, RecvOnly=0
13:45:32 [12053649] 6: RtpApiTalk[1,1], Peer=10.0.0.1:9012, PT=18, FC=2, NewOOB=0
13:45:32 [12053649] 6: ==14:Talking
13:45:43 [12053763] DSP_ch6_check=0
13:45:43 [12053763] 6: Fxs Hangup
13:45:43 [12053763] 6: Bye at Talking
13:45:43 [12053763] 6: ==3:Idle
13:45:43 [12053763] 6: SetFax(1)=0
13:45:44 [12053764] 6: 707=DISCONNECT
13:45:44 [12053764] 6: Release Old Dlg #2


Проблема на всех шлюзах. При выходи на город не понимает сигнал отбоя. И раз через раз после выхода на город АТС не понимает вообще набора клавиш. Везде тональный набор. АТС LG aria SOHO

А лог с 5402?

вот логи с 5402

14:44:26 *** SLMON start to log ***
14:45:26 [5923449] Receive Cmd=1100, ParaLen=5, Para=[Login]
14:45:26 [5923449] Login RU_1.01 == Ver(1.02.38.39.2587 2009/06/15 17:46:00) PId(266.DLink.RU.Lan1Vlan.DualAccess.Wireless.NoPrefix.TR069.jumper25.LifeLine.drt
14:45:26 p) Drv(0.10.37.1) Hw(DSLX) == 0.6.8
14:46:22 [5924006] 1: Fxs Pickup
14:46:22 [5924006] 1: HotLineEnabled with [616]
14:46:22 [5924006] 1: End Input Default Route [1]
14:46:22 [5924006] 1: PhoneBook has GwNo=616, addr=10.0.0.3:5060
14:46:22 [5924006] 1: ==7:Inviting
14:46:22 [5924006] 1: VoIP CallOut, Invite <sip:616@10.0.0.3;user=phone>
14:46:22 [5924007] 1: 716=DIALING
14:46:22 [5924008] 1: 716=PROCEEDING
14:46:23 [5924011] 1: 716=CONNECTED
14:46:23 [5924011] 1: Peer=10.0.0.3:9014, PT=18, RecvOnly=0
14:46:23 [5924011] 1: RtpApiTalk[1,1], Peer=10.0.0.3:9014, PT=18, FC=2, NewOOB=0
14:46:23 [5924011] 1: close fxo break
14:46:23 [5924011] 1: ==14:Talking
14:46:38 [5924169] 1: Fxs Hangup
14:46:38 [5924169] 1: Bye at Talking
14:46:38 [5924170] 1: ==3:Idle
14:46:38 [5924170] 1: SetFax(1)=0
14:46:39 [5924171] 1: 716=DISCONNECT
14:46:39 [5924171] 1: Release Old Dlg #2
14:46:55 [5924336] 1: Fxs Pickup
14:46:55 [5924336] 1: HotLineEnabled with [616]
14:46:55 [5924336] 1: End Input Default Route [1]
14:46:55 [5924336] 1: PhoneBook has GwNo=616, addr=10.0.0.3:5060
14:46:55 [5924336] 1: ==7:Inviting
14:46:55 [5924336] 1: VoIP CallOut, Invite <sip:616@10.0.0.3;user=phone>
14:46:55 [5924337] 1: 716=DIALING
14:46:55 [5924338] 1: 716=PROCEEDING
14:46:56 [5924341] 1: 716=CONNECTED
14:46:56 [5924341] 1: Peer=10.0.0.3:9014, PT=18, RecvOnly=0
14:46:56 [5924341] 1: RtpApiTalk[1,1], Peer=10.0.0.3:9014, PT=18, FC=2, NewOOB=0
14:46:56 [5924341] 1: close fxo break
14:46:56 [5924341] 1: ==14:Talking
14:47:12 [5924506] 1: Fxs Hangup
14:47:12 [5924506] 1: Bye at Talking
14:47:12 [5924506] 1: ==3:Idle
14:47:12 [5924506] 1: SetFax(1)=0
14:47:12 [5924507] 1: 716=DISCONNECT
14:47:12 [5924507] 1: Release Old Dlg #2
14:47:15 [5924531] 1: Fxs Pickup
14:47:15 [5924531] 1: HotLineEnabled with [616]
14:47:15 [5924531] 1: End Input Default Route [1]
14:47:15 [5924531] 1: PhoneBook has GwNo=616, addr=10.0.0.3:5060
14:47:15 [5924531] 1: ==7:Inviting
14:47:15 [5924531] 1: VoIP CallOut, Invite <sip:616@10.0.0.3;user=phone>
14:47:15 [5924532] 1: 716=DIALING
14:47:15 [5924533] 1: 716=PROCEEDING
14:47:15 [5924534] 1: 716=BUSY
14:47:15 [5924534] 1: Release Active Dlg
14:47:15 [5924534] 1: close fxo break
14:47:15 [5924534] 1: ==15:PlayBusyTone
14:47:15 [5924534] 1: 716=DISCONNECT
14:47:15 [5924534] 1: Release Old Dlg #2
14:47:17 [5924554] 1: Fxs Hangup
14:47:17 [5924554] 1: ==3:Idle
14:47:17 [5924554] 1: SetFax(1)=0
14:47:19 [5924575] 1: Fxs Pickup
14:47:19 [5924575] 1: HotLineEnabled with [616]
14:47:19 [5924575] 1: End Input Default Route [1]
14:47:19 [5924575] 1: PhoneBook has GwNo=616, addr=10.0.0.3:5060
14:47:19 [5924575] 1: ==7:Inviting
14:47:19 [5924575] 1: VoIP CallOut, Invite <sip:616@10.0.0.3;user=phone>
14:47:19 [5924576] 1: 716=DIALING
14:47:19 [5924577] 1: 716=PROCEEDING
14:47:19 [5924579] 1: 716=CONNECTED
14:47:19 [5924579] 1: Peer=10.0.0.3:9014, PT=18, RecvOnly=0
14:47:19 [5924580] 1: RtpApiTalk[1,1], Peer=10.0.0.3:9014, PT=18, FC=2, NewOOB=0
14:47:19 [5924580] 1: close fxo break
14:47:20 [5924580] 1: ==14:Talking
14:47:37 [5924753] 1: Fxs Hangup
14:47:37 [5924753] 1: Bye at Talking
14:47:37 [5924753] 1: ==3:Idle
14:47:37 [5924753] 1: SetFax(1)=0
14:47:37 [5924755] 1: 716=DISCONNECT
14:47:37 [5924755] 1: Release Old Dlg #2
14:47:39 [5924771] 1: Fxs Pickup
14:47:39 [5924771] 1: HotLineEnabled with [616]
14:47:39 [5924771] 1: End Input Default Route [1]
14:47:39 [5924771] 1: PhoneBook has GwNo=616, addr=10.0.0.3:5060
14:47:39 [5924771] 1: ==7:Inviting
14:47:39 [5924771] 1: VoIP CallOut, Invite <sip:616@10.0.0.3;user=phone>
14:47:39 [5924772] 1: 716=DIALING
14:47:39 [5924773] 1: 716=PROCEEDING
14:47:39 [5924774] 1: 716=BUSY
14:47:39 [5924774] 1: Release Active Dlg
14:47:39 [5924774] 1: close fxo break
14:47:39 [5924774] 1: ==15:PlayBusyTone
14:47:39 [5924775] 1: 716=DISCONNECT
14:47:39 [5924775] 1: Release Old Dlg #2
14:47:41 [5924799] 1: Fxs Hangup
14:47:41 [5924799] 1: ==3:Idle
14:47:41 [5924799] 1: SetFax(1)=0
14:48:19 [5925177] 1: 716=OFFERING
14:48:19 [5925177] 1: Get CallerId=616
14:48:19 [5925177] 1: Peer=10.0.0.3:9014, PT=18, RecvOnly=0
14:48:19 [5925177] 1: ==12:Alerting
14:48:35 [5925340] 1: 716=DISCONNECT
14:48:35 [5925340] 1: Release Active Dlg
14:48:35 [5925340] 1: ==3:Idle
14:48:36 [5925340] 1: SetFax(1)=0

Судя по логу все в порядке.

Backup конфигурации мне пришлите пожалуйста.

ни чего нормального. Я так и не смог позвонить. Я смог выйти в город, но набрать номер не получается, он не воспринимает набор, и каждый раз был обратный дозвон.

отправил на вашу почту. Тема dvg-5008

Здравствуйте. Мною во вкладке CPT / Cadence Settings выставил значения что в атс и ситуация улучшилась. Но раз через раз шлюз всё равно не понимает сигнал отбоя. По'тому есть вопрос. В атс Даны параметры :
Ring Back Tone
Busy Tone
Error Tone
S-Dial Tone
Что за параметр "Error Tone" и настраивается ли он в шлюзе.
И нужно ли насстраивать CPT / Cadence Settings в шлюзах подключенных напрямую к АТС?

Нужно настраивать на всех шлюзах подключенных к АТС. Error tone - ошибка вызова, обычно делают идентичным Busy Tone.