D-Link • Просмотр темы - Помагите найти проблему.

Сообщения без ответов | Активные темы

Список форумов » Голос по IP (VoIP)

Часовой пояс: UTC + 3 часа

Помагите найти проблему.

Модераторы: Victor Kolosov, Sergei Asmankin, Sergik

Страница 1 из 1

[ Сообщений: 8 ]

Предыдущая тема | Следующая тема

Автор

Сообщение

Plass15

Заголовок сообщения: Помагите найти проблему.

Добавлено: Чт янв 27, 2005 14:54

Зарегистрирован: Ср июл 07, 2004 13:06
Сообщений: 25
Откуда: деревня Москва

Есть следущая схема:

телефон - panasonic 816 - 1104th - инет - 1104th - panasonic 1232 - телефон.

Настроинно по faq.
Все работает. Разговаривать можно.
НО ВОТ ТРАФИК!!!!!!! Бешанный!
Посмотрел TCPDUMP на шлюзе. Постоянно идет трафик вне зависимости разговаривают через длинк или нет!

Привожу debug(без остановки сыпится в кансоль):

Код:

H323ap select codec g711Ulaw64k
H323ap select codec g711Ulaw64k, TxM=2 echo=1
cmEvNewCall(hsCall=7067108) runs
*-*-*-*-*-* Enter SSE section
*-*-*-*-*-* SSE section completed!
0-cmControlStateFastStart
Enter EvChannelNew..6b394c
call0 hsChanIn-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b394c channeName = g711Alaw64k
incoming channel codec: g711Alaw64k
cmEvChannelSetRTCPAddress hsChan = 6b394c
RTCP call: 0, channel: 0
cmEvChannelSetAddress hsChan = 6b394c
call0 ch1-217.119.23.75: 16394-cmEvChannelSetAddress
call0 ch0-ChannelState: Connected
Enter EvChannelNew..6b3ae4
call0 hsChanIn2-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b3ae4 channeName = g711Alaw64k
cmEvChannelSetRTCPAddress hsChan = 6b3ae4
RTCP call: 0, channel: 2
cmEvChannelSetAddress hsChan = 6b3ae4
call0 ch1-217.119.23.75: 16392-cmEvChannelSetAddress

cmEvCallStateChanged(state=cmCallStateOffering, statemode=cmCallStateModeOfferin
gCreate)

0-Offering-cmEvCallStateChanged

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCallSetup)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
------statemode: ConnectedCallSetup------
0-Enter openDeviceChannel
H323ap select codec g711Alaw64k
H323ap select codec g711Alaw64k, TxM=2 echo=1
After connect, h245 connect
0-ControlStateTransportConnected
Enter cmEvCallCapabilities()
(1)(1)(1)
(1)(2)(2)
(1)(3)(3)
(1)(4)(4)
(1)(5)(5)
## Remote Capability Set 5
## [1] g711Alaw64k:
## [2] g711Alaw64k:
## [3] g711Alaw64k:
## [4] g711Alaw64k:
## [5] g729:
the best matched codec is g711Alaw64k
MSDetermination: Master
0-cmControlStateConnected

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCall)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
call0 ch0-ChannelState: Disconnected
call0 ch0-ChannelState: Idle
0-cmControlStateTransportDisconnected

cmEvCallStateChanged(state=cmCallStateDisconnected, statemode=cmCallStateModeDis
connectedNormal)

0-Disconnected-cmEvCallStateChanged reason = -1

cmEvCallStateChanged(state=cmCallStateIdle, statemode=cmCallStateModeDisconnecte
dBusy)

H323ap select codec g711Ulaw64k
H323ap select codec g711Ulaw64k, TxM=2 echo=1
cmEvNewCall(hsCall=7067836) runs
*-*-*-*-*-* Enter SSE section
*-*-*-*-*-* SSE section completed!
0-cmControlStateFastStart
Enter EvChannelNew..6b3c7c
call0 hsChanIn-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b3c7c channeName = g711Alaw64k
incoming channel codec: g711Alaw64k
cmEvChannelSetRTCPAddress hsChan = 6b3c7c
RTCP call: 0, channel: 0
cmEvChannelSetAddress hsChan = 6b3c7c
call0 ch1-217.119.23.75: 16394-cmEvChannelSetAddress
call0 ch0-ChannelState: Connected
Enter EvChannelNew..6b3e14
call0 hsChanIn2-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b3e14 channeName = g711Alaw64k
cmEvChannelSetRTCPAddress hsChan = 6b3e14
RTCP call: 0, channel: 2
cmEvChannelSetAddress hsChan = 6b3e14
call0 ch1-217.119.23.75: 16392-cmEvChannelSetAddress

cmEvCallStateChanged(state=cmCallStateOffering, statemode=cmCallStateModeOfferin
gCreate)

0-Offering-cmEvCallStateChanged

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCallSetup)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
------statemode: ConnectedCallSetup------
0-Enter openDeviceChannel
H323ap select codec g711Alaw64k
H323ap select codec g711Alaw64k, TxM=2 echo=1
After connect, h245 connect
0-ControlStateTransportConnected
Enter cmEvCallCapabilities()
(1)(1)(1)
(1)(2)(2)
(1)(3)(3)
(1)(4)(4)
(1)(5)(5)
## Remote Capability Set 5
## [1] g711Alaw64k:
## [2] g711Alaw64k:
## [3] g711Alaw64k:
## [4] g711Alaw64k:
## [5] g729:
the best matched codec is g711Alaw64k
MSDetermination: Slave
0-cmControlStateConnected

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCall)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
call0 ch0-ChannelState: Disconnected
call0 ch0-ChannelState: Idle
0-cmControlStateTransportDisconnected

cmEvCallStateChanged(state=cmCallStateDisconnected, statemode=cmCallStateModeDis
connectedNormal)

0-Disconnected-cmEvCallStateChanged reason = -1

cmEvCallStateChanged(state=cmCallStateIdle, statemode=cmCallStateModeDisconnecte
dBusy)

H323ap select codec g711Ulaw64k
H323ap select codec g711Ulaw64k, TxM=2 echo=1
cmEvNewCall(hsCall=7068564) runs
*-*-*-*-*-* Enter SSE section
*-*-*-*-*-* SSE section completed!
0-cmControlStateFastStart
Enter EvChannelNew..6b3fac
call0 hsChanIn-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b3fac channeName = g711Alaw64k
incoming channel codec: g711Alaw64k
cmEvChannelSetRTCPAddress hsChan = 6b3fac
RTCP call: 0, channel: 0
cmEvChannelSetAddress hsChan = 6b3fac
call0 ch1-217.119.23.75: 16394-cmEvChannelSetAddress
call0 ch0-ChannelState: Connected
Enter EvChannelNew..6b4144
call0 hsChanIn2-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b4144 channeName = g711Alaw64k
cmEvChannelSetRTCPAddress hsChan = 6b4144
RTCP call: 0, channel: 2
cmEvChannelSetAddress hsChan = 6b4144
call0 ch1-217.119.23.75: 16392-cmEvChannelSetAddress

cmEvCallStateChanged(state=cmCallStateOffering, statemode=cmCallStateModeOfferin
gCreate)

0-Offering-cmEvCallStateChanged

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCallSetup)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
------statemode: ConnectedCallSetup------
0-Enter openDeviceChannel
H323ap select codec g711Alaw64k
H323ap select codec g711Alaw64k, TxM=2 echo=1
After connect, h245 connect
0-ControlStateTransportConnected
Enter cmEvCallCapabilities()
(1)(1)(1)
(1)(2)(2)
(1)(3)(3)
(1)(4)(4)
(1)(5)(5)
## Remote Capability Set 5
## [1] g711Alaw64k:
## [2] g711Alaw64k:
## [3] g711Alaw64k:
## [4] g711Alaw64k:
## [5] g729:
the best matched codec is g711Alaw64k
MSDetermination: Master
0-cmControlStateConnected

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCall)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
call0 ch0-ChannelState: Disconnected
call0 ch0-ChannelState: Idle
0-cmControlStateTransportDisconnected

cmEvCallStateChanged(state=cmCallStateDisconnected, statemode=cmCallStateModeDis
connectedNormal)

0-Disconnected-cmEvCallStateChanged reason = -1

cmEvCallStateChanged(state=cmCallStateIdle, statemode=cmCallStateModeDisconnecte
dBusy)

H323ap select codec g711Ulaw64k
H323ap select codec g711Ulaw64k, TxM=2 echo=1
cmEvNewCall(hsCall=7069292) runs
*-*-*-*-*-* Enter SSE section
*-*-*-*-*-* SSE section completed!
0-cmControlStateFastStart
Enter EvChannelNew..6b42dc
call0 hsChanIn-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b42dc channeName = g711Alaw64k
incoming channel codec: g711Alaw64k
cmEvChannelSetRTCPAddress hsChan = 6b42dc
RTCP call: 0, channel: 0
cmEvChannelSetAddress hsChan = 6b42dc
call0 ch1-217.119.23.75: 16394-cmEvChannelSetAddress
call0 ch0-ChannelState: Connected
Enter EvChannelNew..6b4474
call0 hsChanIn2-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b4474 channeName = g711Alaw64k
cmEvChannelSetRTCPAddress hsChan = 6b4474
RTCP call: 0, channel: 2
cmEvChannelSetAddress hsChan = 6b4474
call0 ch1-217.119.23.75: 16392-cmEvChannelSetAddress

cmEvCallStateChanged(state=cmCallStateOffering, statemode=cmCallStateModeOfferin
gCreate)

0-Offering-cmEvCallStateChanged

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCallSetup)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
------statemode: ConnectedCallSetup------
0-Enter openDeviceChannel
H323ap select codec g711Alaw64k
H323ap select codec g711Alaw64k, TxM=2 echo=1
After connect, h245 connect
0-ControlStateTransportConnected
Enter cmEvCallCapabilities()
(1)(1)(1)
(1)(2)(2)
(1)(3)(3)
(1)(4)(4)
(1)(5)(5)
## Remote Capability Set 5
## [1] g711Alaw64k:
## [2] g711Alaw64k:
## [3] g711Alaw64k:
## [4] g711Alaw64k:
## [5] g729:
the best matched codec is g711Alaw64k
MSDetermination: Slave
0-cmControlStateConnected

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCall)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
^C

usr/config$

Что твориться?
Не ловиться бизи или я что не так настроил.....

Вернуться наверх

alex_u2

Заголовок сообщения:

Добавлено: Чт янв 27, 2005 15:48

IP-PBX member

Зарегистрирован: Чт дек 18, 2003 15:46
Сообщений: 789
Откуда: Dzr NN

Попробуйте
зайти через WEB интерфейс на вкладку Tools ->Voice

установить все 4 кодека G.729a

_________________
Даешь связистов без брака!
AB4790-RIPE

Вернуться наверх

alex_u2

Заголовок сообщения:

Добавлено: Чт янв 27, 2005 15:49

IP-PBX member

Зарегистрирован: Чт дек 18, 2003 15:46
Сообщений: 789
Откуда: Dzr NN

P.S.
на всех устройствах!!!

_________________
Даешь связистов без брака!
AB4790-RIPE

Вернуться наверх

Plass15

Заголовок сообщения:

Добавлено: Чт янв 27, 2005 16:20

Зарегистрирован: Ср июл 07, 2004 13:06
Сообщений: 25
Откуда: деревня Москва

ок.
о результате сообщу!
Только ставлю Echo Canceled в enable.

Вернуться наверх

Plass15

Заголовок сообщения:

Добавлено: Чт янв 27, 2005 16:48

Зарегистрирован: Ср июл 07, 2004 13:06
Сообщений: 25
Откуда: деревня Москва

И все равно!
После первого звонка все повторяется!

Код:

cmEvChannelSetAddress hsChan = 6afb5c
call0 ch1-217.119.23.75: 16392-cmEvChannelSetAddress

cmEvCallStateChanged(state=cmCallStateOffering, statemode=cmCallStateModeOfferin
gCreate)

0-Offering-cmEvCallStateChanged

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCallSetup)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
------statemode: ConnectedCallSetup------
0-Enter openDeviceChannel
H323ap select codec g729AnnexA
H323ap select codec g729AnnexA, TxM=2 echo=1
After connect, h245 connect
0-ControlStateTransportConnected
Enter cmEvCallCapabilities()
(1)(1)(1)
(1)(2)(2)
(1)(3)(3)
(1)(4)(4)
(1)(5)(5)
## Remote Capability Set 5
## [1] g729AnnexA:
## [2] g729AnnexA:
## [3] g729AnnexA:
## [4] g729AnnexA:
## [5] g729:
the best matched codec is g729AnnexA
MSDetermination: Master
0-cmControlStateConnected

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCall)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
call_back_from_VP 16
 call 0 progress tone [4]
Drop the call from IP side
call0 ch0-ChannelState: Disconnected
call0 ch0-ChannelState: Idle
0-cmControlStateTransportDisconnected

cmEvCallStateChanged(state=cmCallStateDisconnected, statemode=cmCallStateModeDis
connectedLocal)

0-Disconnected-cmEvCallStateChanged reason = -1

cmEvCallStateChanged(state=cmCallStateIdle, statemode=cmCallStateModeDisconnecte
dBusy)

H323ap select codec g711Ulaw64k
H323ap select codec g711Ulaw64k, TxM=2 echo=1
cmEvNewCall(hsCall=7071532) runs
*-*-*-*-*-* Enter SSE section
*-*-*-*-*-* SSE section completed!
0-cmControlStateFastStart
Enter EvChannelNew..6afcf4
call0 hsChanIn-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6afcf4 channeName = g729AnnexA
incoming channel codec: g729AnnexA
cmEvChannelSetRTCPAddress hsChan = 6afcf4
RTCP call: 0, channel: 0
cmEvChannelSetAddress hsChan = 6afcf4
call0 ch1-217.119.23.75: 16394-cmEvChannelSetAddress
call0 ch0-ChannelState: Connected
Enter EvChannelNew..6afe8c
call0 hsChanIn2-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6afe8c channeName = g729AnnexA
cmEvChannelSetRTCPAddress hsChan = 6afe8c
RTCP call: 0, channel: 2
cmEvChannelSetAddress hsChan = 6afe8c
call0 ch1-217.119.23.75: 16392-cmEvChannelSetAddress

cmEvCallStateChanged(state=cmCallStateOffering, statemode=cmCallStateModeOfferin
gCreate)

0-Offering-cmEvCallStateChanged

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCallSetup)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
------statemode: ConnectedCallSetup------
0-Enter openDeviceChannel
H323ap select codec g729AnnexA
H323ap select codec g729AnnexA, TxM=2 echo=1
After connect, h245 connect
0-ControlStateTransportConnected
Enter cmEvCallCapabilities()
(1)(1)(1)
(1)(2)(2)
(1)(3)(3)
(1)(4)(4)
(1)(5)(5)
## Remote Capability Set 5
## [1] g729AnnexA:
## [2] g729AnnexA:
## [3] g729AnnexA:
## [4] g729AnnexA:
## [5] g729:
the best matched codec is g729AnnexA
MSDetermination: Slave
0-cmControlStateConnected

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCall)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
call_back_from_VP 16
 call 0 progress tone [4]
Drop the call from IP side
call0 ch0-ChannelState: Disconnected
call0 ch0-ChannelState: Idle
0-cmControlStateTransportDisconnected

cmEvCallStateChanged(state=cmCallStateDisconnected, statemode=cmCallStateModeDis
connectedLocal)

0-Disconnected-cmEvCallStateChanged reason = -1

cmEvCallStateChanged(state=cmCallStateIdle, statemode=cmCallStateModeDisconnecte
dBusy)

H323ap select codec g711Ulaw64k
H323ap select codec g711Ulaw64k, TxM=2 echo=1
cmEvNewCall(hsCall=7072260) runs
*-*-*-*-*-* Enter SSE section
*-*-*-*-*-* SSE section completed!
0-cmControlStateFastStart
Enter EvChannelNew..6b0024
call0 hsChanIn-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b0024 channeName = g729AnnexA
incoming channel codec: g729AnnexA
cmEvChannelSetRTCPAddress hsChan = 6b0024
RTCP call: 0, channel: 0
cmEvChannelSetAddress hsChan = 6b0024
call0 ch1-217.119.23.75: 16394-cmEvChannelSetAddress
call0 ch0-ChannelState: Connected
Enter EvChannelNew..6b01bc
call0 hsChanIn2-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b01bc channeName = g729AnnexA
cmEvChannelSetRTCPAddress hsChan = 6b01bc
RTCP call: 0, channel: 2
cmEvChannelSetAddress hsChan = 6b01bc
call0 ch1-217.119.23.75: 16392-cmEvChannelSetAddress

cmEvCallStateChanged(state=cmCallStateOffering, statemode=cmCallStateModeOfferin
gCreate)

0-Offering-cmEvCallStateChanged

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCallSetup)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
------statemode: ConnectedCallSetup------
0-Enter openDeviceChannel
H323ap select codec g729AnnexA
H323ap select codec g729AnnexA, TxM=2 echo=1
After connect, h245 connect
0-ControlStateTransportConnected
Enter cmEvCallCapabilities()
(1)(1)(1)
(1)(2)(2)
(1)(3)(3)
(1)(4)(4)
(1)(5)(5)
## Remote Capability Set 5
## [1] g729AnnexA:
## [2] g729AnnexA:
## [3] g729AnnexA:
## [4] g729AnnexA:
## [5] g729:
the best matched codec is g729AnnexA
MSDetermination: Master
0-cmControlStateConnected

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCall)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
call_back_from_VP 16
 call 0 progress tone [4]
Drop the call from IP side
call0 ch0-ChannelState: Disconnected
call0 ch0-ChannelState: Idle
0-cmControlStateTransportDisconnected

cmEvCallStateChanged(state=cmCallStateDisconnected, statemode=cmCallStateModeDis
connectedLocal)

0-Disconnected-cmEvCallStateChanged reason = -1

cmEvCallStateChanged(state=cmCallStateIdle, statemode=cmCallStateModeDisconnecte
dBusy)

H323ap select codec g711Ulaw64k
H323ap select codec g711Ulaw64k, TxM=2 echo=1
cmEvNewCall(hsCall=7072988) runs
*-*-*-*-*-* Enter SSE section
*-*-*-*-*-* SSE section completed!
0-cmControlStateFastStart
Enter EvChannelNew..6b0354
call0 hsChanIn-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b0354 channeName = g729AnnexA
incoming channel codec: g729AnnexA
cmEvChannelSetRTCPAddress hsChan = 6b0354
RTCP call: 0, channel: 0
cmEvChannelSetAddress hsChan = 6b0354
call0 ch1-217.119.23.75: 16394-cmEvChannelSetAddress
call0 ch0-ChannelState: Connected
Enter EvChannelNew..6b04ec
call0 hsChanIn2-cmEvChannelNew Send
cmEvChannelParameters hsChannel: 6b04ec channeName = g729AnnexA
cmEvChannelSetRTCPAddress hsChan = 6b04ec
RTCP call: 0, channel: 2
cmEvChannelSetAddress hsChan = 6b04ec
call0 ch1-217.119.23.75: 16392-cmEvChannelSetAddress

cmEvCallStateChanged(state=cmCallStateOffering, statemode=cmCallStateModeOfferin
gCreate)

0-Offering-cmEvCallStateChanged

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCallSetup)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
------statemode: ConnectedCallSetup------
0-Enter openDeviceChannel
H323ap select codec g729AnnexA
H323ap select codec g729AnnexA, TxM=2 echo=1
After connect, h245 connect
0-ControlStateTransportConnected
Enter cmEvCallCapabilities()
(1)(1)(1)
(1)(2)(2)
(1)(3)(3)
(1)(4)(4)
(1)(5)(5)
## Remote Capability Set 5
## [1] g729AnnexA:
## [2] g729AnnexA:
## [3] g729AnnexA:
## [4] g729AnnexA:
## [5] g729:
the best matched codec is g729AnnexA
MSDetermination: Master
0-cmControlStateConnected

cmEvCallStateChanged(state=cmCallStateConnected, statemode=cmCallStateModeConnec
tedCall)

0-Connected-cmEvCallStateChanged
Callee----->
 fs_flag[0]=1
^C

usr/config$
usr/config$ call_back_from_VP 16
 call 0 progress tone [4]
Drop the call from IP side
call0 ch0-ChannelState: Disconnected
call0 ch0-ChannelState: Idle
0-cmControlStateTransportDisconnected

cmEvCallStateChanged(state=cmCallStateDisconnected, statemode=cmCallStateModeDis
connectedLocal)

0-Disconnected-cmEvCallStateChanged reason = -1

cmEvCallStateChanged(state=cmCallStateIdle, statemode=cmCallStateModeDisconnecte
dBusy)

H323ap select codec g711Ulaw64k
H323ap select codec g711Ulaw64k, TxM=2 echo=1
^C^C

usr/config$

Вернуться наверх

alex_u2

Заголовок сообщения:

Добавлено: Чт янв 27, 2005 16:51

IP-PBX member

Зарегистрирован: Чт дек 18, 2003 15:46
Сообщений: 789
Откуда: Dzr NN

1. H245tunneling выключен?
2. Все в точно в соответствии с факом?
3. версии прошивок?
4. настройки - адреса, макси и шлюзы устройств

_________________
Даешь связистов без брака!
AB4790-RIPE

Вернуться наверх

Plass15

Заголовок сообщения:

Добавлено: Чт янв 27, 2005 17:04

Зарегистрирован: Ср июл 07, 2004 13:06
Сообщений: 25
Откуда: деревня Москва

(1)
Special Voice function support manipulation
T.38(FAX) support : Disabled.
T.38(FAX) ECM : Enabled.
FastStart support : Enabled.
Tunnelled H.245 support : Disabled.
H.245 message after FastStart : Enabled.

(2)
Да

(3)
1.02
(4) ?????

Вернуться наверх

Plass15

Заголовок сообщения:

Добавлено: Пт фев 18, 2005 14:03

Зарегистрирован: Ср июл 07, 2004 13:06
Сообщений: 25
Откуда: деревня Москва

Проблемма - решена!
Все оказалось просто!
К одной станции был подключен телефон с функцией "месадж"...

Вернуться наверх

Страница 1 из 1

[ Сообщений: 8 ]

Список форумов » Голос по IP (VoIP)

Часовой пояс: UTC + 3 часа

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 4

Вы не можете начинать темы
Вы не можете отвечать на сообщения
Вы не можете редактировать свои сообщения
Вы не можете удалять свои сообщения
Вы не можете добавлять вложения