Добрый день,

проблема с настройкой данной связки: DGS-3420-28PC + Freeradius ( 3.0.10 )

Ready to process requests
(0) Received Access-Request Id 22 from 10.10.9.10:1034 to 10.10.9.5:1812 length 85
(0) User-Name = "user"
(0) User-Password = "\037I\251\237\243tO\346b!\317 h[\177O"
(0) NAS-IP-Address = 10.10.9.10
(0) NAS-Identifier = "Test"
(0) NAS-Port-Type = Virtual
(0) Service-Type = Framed-User
(0) Framed-Protocol = PPP
(0) # Executing section authorize from file /etc/raddb/sites-enabled/default
(0) authorize {
(0) policy filter_username {
(0) if (!&User-Name) {
(0) if (!&User-Name) -> FALSE
(0) if (&User-Name =~ / /) {
(0) if (&User-Name =~ / /) -> FALSE
(0) if (&User-Name =~ /@.*@/ ) {
(0) if (&User-Name =~ /@.*@/ ) -> FALSE
(0) if (&User-Name =~ /\.\./ ) {
(0) if (&User-Name =~ /\.\./ ) -> FALSE
(0) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) {
(0) if ((&User-Name =~ /@/) && (&User-Name !~ /@(.+)\.(.+)$/)) -> FALSE
(0) if (&User-Name =~ /\.$/) {
(0) if (&User-Name =~ /\.$/) -> FALSE
(0) if (&User-Name =~ /@\./) {
(0) if (&User-Name =~ /@\./) -> FALSE
(0) } # policy filter_username = notfound
(0) [preprocess] = ok
(0) [chap] = noop
(0) [mschap] = noop
(0) [digest] = noop
(0) suffix: Checking for suffix after "@"
(0) suffix: No '@' in User-Name = "user", looking up realm NULL
(0) suffix: No such realm "NULL"
(0) [suffix] = noop
(0) eap: No EAP-Message, not doing EAP
(0) [eap] = noop
(0) files: users: Matched entry DEFAULT at line 181
(0) [files] = ok
(0) [expiration] = noop
(0) [logintime] = noop
(0) pap: WARNING: No "known good" password found for the user. Not setting Auth-Type
(0) pap: WARNING: Authentication will fail unless a "known good" password is available
(0) [pap] = noop
(0) } # authorize = ok
(0) ERROR: No Auth-Type found: rejecting the user via Post-Auth-Type = Reject
(0) Failed to authenticate the user
(0) Login incorrect (No Auth-Type found: rejecting the user via Post-Auth-Type = Reject): [user/?I???tO?b!? h[?O] (from client switch port 0)
(0) WARNING: Unprintable characters in the password. Double-check the shared secret on the server and the NAS!
(0) Using Post-Auth-Type Reject
(0) # Executing group from file /etc/raddb/sites-enabled/default
(0) Post-Auth-Type REJECT {
(0) attr_filter.access_reject: EXPAND %{User-Name}
(0) attr_filter.access_reject: --> user
(0) attr_filter.access_reject: Matched entry DEFAULT at line 11
(0) [attr_filter.access_reject] = updated
(0) [eap] = noop
(0) policy remove_reply_message_if_eap {
(0) if (&reply:EAP-Message && &reply:Reply-Message) {
(0) if (&reply:EAP-Message && &reply:Reply-Message) -> FALSE
(0) else {
(0) [noop] = noop
(0) } # else = noop
(0) } # policy remove_reply_message_if_eap = noop
(0) } # Post-Auth-Type REJECT = updated
(0) Delaying response for 1.000000 seconds
Waking up in 0.3 seconds.
Waking up in 0.6 seconds.
(0) Sending delayed response

************************************************
cat /etc/raddb/users
user Cleartext-Password := "1234"
Dlink-User-Level = 3
************************************************

Добрый день.

На всякий случай выкладываю решение данной ситуации.

В файле users нужно закомментировать строки:

DEFAULT Framed-Protocol == PPP
Framed-Protocol = PPP,
Framed-Compression = Van-Jacobson-TCP-IP

DEFAULT Hint == "CSLIP"
Framed-Protocol = SLIP,
Framed-Compression = Van-Jacobson-TCP-IP

DEFAULT Hint == "SLIP"
Framed-Protocol = SLIP

После этого авторизация должна пройти успешно, если остальное всё правильно настроено.

_________________
С уважением,
Бигаров Руслан.