

CFE version 1.0.37-104.4 for BCM96338 (32bit,SP,BE)
Build Date:   29 10:38:44 UTC 2011 (D-Link Russia)
Copyright (C) 2000-2009 Broadcom Corporation.

Serial flash device: name , id 0xef15 size 4096KB
Total Flash size: 4096K with 64 sectors
100 MB Full-Duplex (auto-neg)
Chip ID: BCM6338A2, MIPS: 240MHz
Total Memory: 16777216 bytes (16MB)
Boot Address: 0xb8000000

Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-12)                   : 96333AWG_F7S
Number of MAC Addresses (1-32)    : 2
Base MAC Address                  : 1c:af:f7:b3:50:38
PSI Size (1-64) KBytes            : 24
Enable Backup PSI [0|1]           : 0
System Log Size (0-256) KBytes    : 0

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x801c3018
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x801c3018
Closing network.
Closing DMA Channels.
Starting program at 0x801c3018
Linux version 2.6.8.1 (zhouyu@localhost.localdomain) (gcc version 3.4.2) #1 Mon Nov 29 21:55:02 CST 2010
Serial flash device: name NXW25P32, id 0xef15, size 4096KB
96333AWG_F7S prom init
CPU revision is: 00029010
Determined physical RAM map:
 memory: 00fa0000 @ 00000000 (usable)
On node 0 totalpages: 4000
  DMA zone: 4000 pages, LIFO batch:1
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 64 (order 6: 512 bytes)
Using 120.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 13828k/16000k available (1508k kernel code, 2152k reserved, 227k data, 72k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80e00000 ... 0x80f00000>
Calibrating delay loop... 239.20 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...  unavailable.
NET: Registered protocol family 16
Total Flash size: 4096K with 1024 sectors
File system address: 0xbfc10100
Blk# BlkOff Blks  MemLen Partition Name
   0   1408    1    1024 NVRAM
1010      0    6   24576 Config 2
1016      0    2    8192 Scratch PAD
1018      0    6   24576 Config 1
Can't analyze prologue code at 80187cb4
Initializing Cryptographic API
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
brcmboard: brcm_board_init entry
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX
Broadcom BCM6338A2 Ethernet Network Device v0.3 Nov 29 2010 21:54:20
Config PHY Switch Through MDIO Pseudo PHY Interface
BCM63xx_ENET: 100 MB Full-Duplex (auto-neg)
====>PAGE_MANAGEMENT=02, REG_DEV_ID=30, val32=00000000
ethsw: found bcm5325e!
eth0: MAC Address: 1C:AF:F7:B3:50:38
eth0 Link UP.
eth0.2: MAC Address: 1C:AF:F7:B3:50:38
eth0.3: MAC Address: 1C:AF:F7:B3:50:38
eth0.4: MAC Address: 1C:AF:F7:B3:50:38
eth0.5: MAC Address: 1C:AF:F7:B3:50:38
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 72k freed
init started:  BusyBox v1.00 (2010.11.29-13:57+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5


BusyBox v1.00 (2010.11.29-13:57+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
insmod: cannot insert `/lib/modules/2.6.8.1/extra/wl.ko': Success (1): Success
BcmAdsl_Initialize=0xC00663E8, g_pFnNotifyCallback=0xC0080FE4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA0FFFFF8, 0xFFFFF6FF 0xFFFFFFCF
AdslCoreHwReset:  AdslOemDataAddr = 0xA0FEF96C
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!

==>   Bcm963xx Software Version: 3.12L.01.A2pB025c1.d20k_rc2   <==

device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
wlctl: wl driver adapter not found
