3 syslogd started: BusyBox v1.19.2
Jan 1 00:00:03 kernel: gpiom: led support enabled.
Jan 1 00:00:03 kernel: IRQ 32/gpiom: IRQF_DISABLED is not guaranteed on shared IRQs
Jan 1 00:00:03 kernel: [RTL_NIC]:(success): Dev eth0 is opened!
Jan 1 00:00:03 kernel: -------> Set MIB from /etc/Wireless/RTL8192CD.dat
Jan 1 00:00:03 kernel: <------- Set MIB from /etc/Wireless/RTL8192CD.dat Success
Jan 1 00:00:03 kernel: ************* Initialize MAC/PHY parameter *************
Jan 1 00:00:03 kernel: [MAC_REG_8192Emp]
Jan 1 00:00:03 kernel: [PHY_REG_8192Emp]
Jan 1 00:00:03 kernel: RTL8192E_MAC_PHY_Parameter_v043_MP_20141229
Jan 1 00:00:03 kernel: [PHY_REG_PG_8192Emp]
Jan 1 00:00:03 kernel: RL6286_MAC_PHY_Parameter_v024_20130125
Jan 1 00:00:03 kernel: [AGC_TAB_8192Emp]
Jan 1 00:00:03 kernel: RTL8192E_MAC_PHY_Parameter_v043_MP_20141229
Jan 1 00:00:03 kernel: RadioA_8192Emp
Jan 1 00:00:03 kernel: RTL8192E_MAC_PHY_Parameter_v043_MP_20141229
Jan 1 00:00:03 kernel: [RadioB_8192Emp]
Jan 1 00:00:03 kernel: RTL8192E_MAC_PHY_Parameter_v043_MP_20141229
Jan 1 00:00:03 kernel: [PHY_ConfigTXPwrTrackingWithParaFile]
Jan 1 00:00:03 kernel: [TxPowerTrack_AP]
Jan 1 00:00:04 kernel: [RTL_NIC]:(success): Dev eth1 is opened!
Jan 1 00:00:04 kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 1 00:00:04 init_lan[35]: start
Jan 1 00:00:04 init_lan[35]: no grouping style
Jan 1 00:00:04 init_lan[35]: iface br0
Jan 1 00:00:04 config_bridge[35]: iface br0 ip 192.168.1.10 255.255.255.0
Jan 1 00:00:04 config_bridge[35]: create up event for LAN6. iface br0
Jan 1 00:00:05 calculate_file_md5sum[35]: Error: can't open file /tmp/dnsmasq.conf
Jan 1 00:00:05 recheck_dnsmasq[35]: MD5 sum calculation of /tmp/dnsmasq.conf before or/and after fail, restarting DNSMASQ
Jan 1 00:00:05 kernel: message received before monitor task is initialized kerSysSendtoNlMonTask
Jan 1 00:00:05 kernel: [RTL_NIC]: Wan link is down!
Jan 1 00:00:05 kernel: device eth0.2 entered promiscuous mode
Jan 1 00:00:05 kernel: device eth0 entered promiscuous mode
Jan 1 00:00:05 kernel: device wlan0 entered promiscuous mode
Jan 1 00:00:05 kernel: [RTL_NIC]: Add VLAN 2 with portmask: 0x10f, tagmask: 0x100 to switch core
Jan 1 00:00:05 kernel: [RTL_NIC]: Update netif for eth0, vid: 2, portmask: 0x10f
Jan 1 00:00:06 kernel: [RTL_NIC]: Add VLAN 1 with portmask: 0x10, tagmask: 0x0 to switch core
Jan 1 00:00:06 kernel: [RTL_NIC]: Update netif for eth1, vid: 1, portmask: 0x10
Jan 1 00:00:06 kernel: message received before monitor task is initialized kerSysSendtoNlMonTask
Jan 1 00:00:06 kernel: [RTL_NIC]: Wan link is up!
Jan 1 00:00:06 kernel: message received before monitor task is initialized kerSysSendtoNlMonTask
Jan 1 00:00:06 kernel: [RTL_NIC]: Wan link is down!
Jan 1 00:00:06 kernel: br0: port 2(wlan0) entering learning state
Jan 1 00:00:06 kernel: br0: port 1(eth0.2) entering learning state
Jan 1 00:00:06 init_mii[35]: flow-control on WAN disabled
Jan 1 00:00:06 resident[35]: init wan
Jan 1 00:00:06 kernel: [RTL_NIC]:(success): Dev eth1 is closed!
Jan 1 00:00:06 kernel: [RTL_NIC]:(success): Dev eth1 is opened!
Jan 1 00:00:06 kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 1 00:00:06 dms_srv_httpd_start[35]: start
Jan 1 00:00:06 check_yasslews_certificate[35]: ok
Jan 1 00:00:06 dms_yasslews_start[35]: pid 219
Jan 1 00:00:06 dms_yasslews_start[35]: pid 220
Jan 1 00:00:06 telnet-start[35]: begin...
Jan 1 00:00:06 telnet-start[35]: running on 23 port
Jan 1 00:00:06 telnet-start[35]: succes!
Jan 1 00:00:06 restart_udpxy[35]: udpxy has restarted
Jan 1 00:00:06 stop_udpxy[35]: udpxy has stoped
Jan 1 00:00:07 kernel: wlan0: A wireless client is associated - 14:36:C6:7C:91:30
Jan 1 00:00:07 kernel: wlan0: WPA2-AES PSK authentication in progress...
Jan 1 00:00:07 kernel: wlan0: A wireless client is associated - 14:36:C6:7C:91:30
Jan 1 00:00:07 restart_udpxy[35]: udpxy has restarted wan =ppp0
Jan 1 00:00:07 resident[35]: stop igmpx
Jan 1 00:00:07 kernel: wlan0: Open and authenticated
Jan 1 00:00:07 start_udpxy[35]: udpxy has started on *.^Xl*.^Xt*.m,*.l^P*. 8.I.*.*p
Jan 1 00:00:07 start_udpxy[35]: udpxy has started on ppp0 with pid 251
Jan 1 00:00:07 dms_check_config_by_default[35]: this config is NO default
Jan 1 00:00:07 dms_redirect_state_output[35]: is_active = no is_factory = no is_con_up_v4 = no is_con_up_v6 = no is_flashing = no is_configuring = no
Jan 1 00:00:07 dms_redirect_state_output[35]: eth: off dsl: off usb: off configuring off default port: ethernet
Jan 1 00:00:07 dms_redirect_cfg_output[35]: enable = yes, cable = yes, connections = yes, factory = yes, flashing = yes
Jan 1 00:00:07 kernel: message received before monitor task is initialized kerSysSendtoNlMonTask
Jan 1 00:00:07 kernel: [RTL_NIC]: Wan link is up!
Jan 1 00:00:07 kernel: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Jan 1 00:00:08 dms_redirect_start[35]: start
Jan 1 00:00:08 dms_check_config_by_default[35]: this config is NO default
Jan 1 00:00:08 nvram[37]: client accepted
Jan 1 00:00:08 nvram[37]: nvram get: [roam-enabled = false]
Jan 1 00:00:09 recheck_dnsmasq[35]: MD5 sum of /tmp/dnsmasq.conf before and after matching, not restarting DNSMASQ
Jan 1 00:00:10 kernel: monitor task is initialized pid= 274
Jan 1 00:00:10 link_watcher_start[35]: link watcher start with status 1
Jan 1 00:00:10 resident[35]: Out init_device
Jan 1 00:00:10 resident[279]: record = action:up;source:start_ip_lan6;iface:br0;ip_type:6;
Jan 1 00:00:10 resident[279]: phys_iface br0
Jan 1 00:00:10 resident_ipoe_handler[279]: ip_type = 6
Jan 1 00:00:10 resident_ipoe_handler[279]: name: br0
Jan 1 00:00:10 resident_mng[34]: RESIDENT WORKER is running.
Jan 1 00:00:10 resident[279]: resident_ipoe_handler - l2:br0, l3:br0, tun:, ip_type:1
Jan 1 00:00:10 ip_is_up6[279]: lan6 connection
Jan 1 00:00:10 nvram[37]: client accepted
Jan 1 00:00:10 nvram[37]: nvram get: [pfx1 = (null)]
Jan 1 00:00:10 nvram[37]: client accepted
Jan 1 00:00:10 nvram[37]: nvram get: [pfx2 = (null)]
Jan 1 00:00:10 pfx_pton[279]: error: param is null
Jan 1 00:00:10 DMS_NL_API[279]: Rtnetlink answer: File exists
Jan 1 00:00:10 update_dhcp6_range[279]: cur_start_ipv6 fd01::1
Jan 1 00:00:10 update_dhcp6_range[279]: cur_end_ipv6 fd01::ffff:ffff:ffff:ffff
Jan 1 00:00:10 update_dhcp6_range[279]: ip_start fd01::1
Jan 1 00:00:10 update_dhcp6_range[279]: ip_end fd01::ffff:ffff:ffff:ffff
Jan 1 00:00:11 recheck_dnsmasq[279]: MD5 sum of /tmp/dnsmasq.conf before and after matching, not restarting DNSMASQ
Jan 1 00:00:11 DMS_NL_API[279]: Rtnetlink answer: File exists
Jan 1 00:00:11 recheck_dnsmasq[279]: MD5 sum of /tmp/dnsmasq.conf before and after matching, not restarting DNSMASQ
Jan 1 00:00:11 ipoe_handler_v6[279]: up6: started
Jan 1 00:00:11 resident_ipoe_handler[279]: is done on iface br0 with action up
Jan 1 00:00:11 resident_ipoe_handler[279]: exit
Jan 1 00:00:11 resident_phy_link_handler[283]: record = phy:-5;status:1
Jan 1 00:00:11 resident_phy_link_handler[283]: phy - -5, status - 1
Jan 1 00:00:11 dms_redirect_state_output[283]: is_active = yes is_factory = no is_con_up_v4 = no is_con_up_v6 = no is_flashing = no is_configuring = no
Jan 1 00:00:11 dms_redirect_state_output[283]: eth: on dsl: off usb: off configuring off default port: ethernet
Jan 1 00:00:11 dms_redirect_cfg_output[283]: enable = yes, cable = yes, connections = yes, factory = yes, flashing = yes
Jan 1 00:00:11 start_stop_all_eth_wan_links_on_l2[283]: Begin: status 1
Jan 1 00:00:11 start_stop_wan_link_on_l2[283]: start with iface: eth1, status: 1
Jan 1 00:00:11 resident[283]: start pppd on eth1_3
Jan 1 00:00:11 resident[283]: stop pppd on eth1_3
Jan 1 00:00:11 resident[283]: set lock on eth1_3, with "/var/lock/eth1_3.lock"
Jan 1 00:00:11 wan_down[283]: name = ppp0
Jan 1 00:00:11 update_wan_firewall[283]: firewall enable
Jan 1 00:00:11 triggerPingRespond[283]: OK
Jan 1 00:00:11 dms_redirect_state_output[283]: is_active = yes is_factory = no is_con_up_v4 = no is_con_up_v6 = no is_flashing = no is_configuring = no
Jan 1 00:00:11 dms_redirect_state_output[283]: eth: on dsl: off usb: off configuring off default port: ethernet
Jan 1 00:00:11 dms_redirect_cfg_output[283]: enable = yes, cable = yes, connections = yes, factory = yes, flashing = yes
Jan 1 00:00:11 resident[283]: stopped link(contype:ppp, iface:eth1_3)
Jan 1 00:00:13 nvram[37]: client accepted
Jan 1 00:00:13 nvram[37]: nvram get: [sess_id = 1001:DC:38:E1:F7:DC:F6]
Jan 1 00:00:13 start_pppd[283]: using old session parameters: 1001:DC:38:E1:F7:DC:F6
Jan 1 00:00:14 pppd[292]: RP-PPPoE plugin version 3.3 compiled against pppd 2.4.4
Jan 1 00:00:14 pppd[293]: entering dlock, dfd = -1
Jan 1 00:00:14 pppd[293]: dlock: locked
Jan 1 00:00:14 pppd[293]: pppd 2.4.4 started by admin, uid 0
Jan 1 00:00:14 pppd[293]: PPPD AUTH: starting to listen connection.
Jan 1 00:00:14 pppd[293]: Sent PADT
Jan 1 00:00:14 pppd[293]: PPP session is 1700
Jan 1 00:00:16 kernel: br0: port 2(wlan0) entering forwarding state
Jan 1 00:00:16 kernel: br0: port 1(eth0.2) entering forwarding state
Jan 1 00:00:16 resident[283]: start ipoe
Jan 1 00:00:16 start_ip[283]: begin (eth1 -> eth1_4)
Jan 1 00:00:16 resident[283]: start ipoe (v0) on eth1
Jan 1 00:00:16 start_ip[283]: pos = 9
Jan 1 00:00:16 start_stop_wan_link_on_l2[283]: End iface: eth1, status: 1
Jan 1 00:00:16 start_stop_all_eth_wan_links_on_l2[283]: End: status 1
Jan 1 00:00:16 udhcpc[295]: UDHCP start..
Jan 1 00:00:16 udhcpc[295]: udhcp client (v0.9.
started (iface: eth1, connect: 4)
Jan 1 00:00:16 udhcpc[295]: interface eth1 index 18
Jan 1 00:00:16 udhcpc[295]: interface eth1 hwaddr 70:62:b8:8d:ad:a2
Jan 1 00:00:16 udhcpc[295]: interface eth1 mtu is 1500
Jan 1 00:00:16 udhcpc[297]: execle'ing /tmp/udhcpc with name deconfig
Jan 1 00:00:16 event[297]: send event "ipoe down"
Jan 1 00:00:16 resident[279]: record = action:down;iface:eth1;contag:4;
Jan 1 00:00:16 resident[279]: phys_iface eth1
Jan 1 00:00:16 resident_ipoe_handler[279]: ip_type = (null)
Jan 1 00:00:16 resident[279]: resident_ipoe_handler - Set default type: ipv4
Jan 1 00:00:16 resident[279]: phys_iface
Jan 1 00:00:16 resident[279]: resident_ipoe_handler - 2
Jan 1 00:00:16 resident_ipoe_handler[279]: name: eth1_4
Jan 1 00:00:17 udhcpc[295]: Opening raw socket on ifindex 18
Jan 1 00:00:17 udhcpc[295]: Sending discover...
Jan 1 00:00:17 udhcpc[295]: Sending select for 10.113.79.247...
Jan 1 00:00:17 resident[279]: resident_ipoe_handler - l2:eth1, l3:eth1_4, tun:, ip_type:0
Jan 1 00:00:17 resident[279]: ip_is_down on eth1_4
Jan 1 00:00:17 DMS_NL_API[279]: Cannot find device: eth1_4
Jan 1 00:00:17 DMS_ROUTE_ERROR[279]: DEL 192.168.100.2 via 10.113.76.1 dev eth1_4 metr 0 table 254 (ip_is_down)
Jan 1 00:00:17 wan_down[279]: name = eth1_4
Jan 1 00:00:17 update_wan_firewall[279]: firewall enable
Jan 1 00:00:17 resident_phy_link_handler[283]: Exit
Jan 1 00:00:17 udhcpc[295]: Lease of 10.113.79.247 obtained, lease time 28800
Jan 1 00:00:17 udhcpc[320]: A reciving size string is 4
Jan 1 00:00:17 udhcpc[320]: execle'ing /tmp/udhcpc with name bound
Jan 1 00:00:17 event[320]: send event "ipoe up"
Jan 1 00:00:17 triggerPingRespond[279]: OK
Jan 1 00:00:17 dms_redirect_state_output[279]: is_active = yes is_factory = no is_con_up_v4 = no is_con_up_v6 = no is_flashing = no is_configuring = no
Jan 1 00:00:17 dms_redirect_state_output[279]: eth: on dsl: off usb: off configuring off default port: ethernet
Jan 1 00:00:17 dms_redirect_cfg_output[279]: enable = yes, cable = yes, connections = yes, factory = yes, flashing = yes
Jan 1 00:00:17 autoupdate[279]: Config reset
Jan 1 00:00:17 dms_reset_uptime[279]: enter key eth1_4
Jan 1 00:00:17 dms_reset_uptime[279]: unable to remove file /tmp/stat.eth1_4
Jan 1 00:00:17 resident_ipoe_handler[279]: is done on iface eth1_4 with action down
Jan 1 00:00:17 resident_ipoe_handler[279]: exit
Jan 1 00:00:17 resident[279]: record = action:up;iface:eth1;contag:4;ipaddr:10.113.79.247 ;netmask:255.255.252.0 ;gateway:10.113.76.1 ;leasetime:28800 ;serverid:192.168.100.2 ;ntpsrv:46.61.192.15 46.61.192.16 ;dns1:46.61.192.15;dns2:46.61.192.16;
Jan 1 00:00:17 resident[279]: phys_iface eth1
Jan 1 00:00:17 resident_ipoe_handler[279]: ip_type = (null)
Jan 1 00:00:17 resident[279]: resident_ipoe_handler - Set default type: ipv4
Jan 1 00:00:17 resident[279]: phys_iface
Jan 1 00:00:17 resident[279]: resident_ipoe_handler - 2
Jan 1 00:00:17 resident_ipoe_handler[279]: name: eth1_4
Jan 1 00:00:17 resident[279]: resident_ipoe_handler - l2:eth1, l3:eth1_4, tun:, ip_type:0
Jan 1 00:00:17 resident[279]: resident_ipoe_handler - ipv4
Jan 1 00:00:17 dms_arp_probe_select_bestaddr_v4[279]: Nothing to probe, got only one address
Jan 1 00:00:17 resident_ipoe_handler[279]: Got '10.113.76.1' as defroutes from upstream
Jan 1 00:00:17 resident_ipoe_handler[279]: Set '10.113.76.1' as real defroute
Jan 1 00:00:17 resident[279]: start ip_is_up on iface eth1_4
Jan 1 00:00:17 resident[279]: ip_is_up for link eth1_4
Jan 1 00:00:17 DMS_ROUTE_SUCCESS[279]: ADD default via 10.113.76.1 dev eth1 metr 101 table 253 (ip_is_up)
Jan 1 00:00:17 DMS_ROUTE_SUCCESS[279]: ADD 192.168.100.2 via 10.113.76.1 dev eth1 metr 0 table 254 (ip_is_up)
Jan 1 00:00:17 set_dhcp_routes[279]: set routes for iface eth1
Jan 1 00:00:17 DMS_ROUTE_SUCCESS[279]: ADD 224.1.0.0/16 via 10.113.79.247 dev eth1 metr 1 table 254 (set_static_routes)
Jan 1 00:00:17 DMS_ROUTE_SUCCESS[279]: ADD 46.61.192.15 via 10.113.76.1 dev eth1 metr 0 table 254 (ip_is_up)
Jan 1 00:00:17 DMS_ROUTE_SUCCESS[279]: ADD 46.61.192.16 via 10.113.76.1 dev eth1 metr 0 table 254 (ip_is_up)
Jan 1 00:00:17 update_wan_firewall[279]: firewall enable
Jan 1 00:00:17 triggerPingRespond[279]: OK
Jan 1 00:00:17 update_ripd[279]: update rip
Jan 1 00:00:17 resident[279]: update igmpx
Jan 1 00:00:17 resident[279]: stop igmpx
Jan 1 00:00:17 resident[279]: global igmp not enable!
Jan 1 00:00:17 restart_udpxy[279]: udpxy has restarted
Jan 1 00:00:17 stop_udpxy[279]: udpxy has stoped
Jan 1 00:00:18 restart_udpxy[279]: udpxy has restarted wan =ppp0
Jan 1 00:00:18 resident[279]: stop igmpx
Jan 1 00:00:18 start_udpxy[279]: udpxy has started on *.^Xl*.^Xt*.m,*.l^P*. 8.C.*.*p
Jan 1 00:00:18 start_udpxy[279]: udpxy has started on ppp0 with pid 378
Jan 1 00:00:19 recheck_dnsmasq[279]: MD5 sum of /tmp/dnsmasq.conf before and after matching, not restarting DNSMASQ
Jan 1 00:00:19 resident_ipoe_handler[279]: is done on iface eth1_4 with action up
Jan 1 00:00:19 resident_ipoe_handler[279]: exit
Jan 1 00:00:19 pppd[293]: Using interface ppp0
Jan 1 00:00:19 pppd[293]: Connect: ppp0 <--> eth1
Jan 1 00:00:19 pppd[293]: PAP authentication succeeded
Jan 1 00:00:19 pppd[293]: peer from calling number DC:38:E1:F6:D4:52 authorized
Jan 1 00:00:19 pppd[293]: local IP address 46.63.212.99
Jan 1 00:00:19 pppd[293]: remote IP address 178.34.128.11
Jan 1 00:00:19 pppd[293]: primary DNS address 94.255.29.30
Jan 1 00:00:19 pppd[293]: secondary DNS address 94.255.29.222
Jan 1 00:00:19 resident_ppp_handler[386]: record = action:up;iface:ppp0;link:eth1_3;ipaddr:46.63.212.99;netmask:255.255.255.255;gateway:178.34.128.11;dns1:94.255.29.30;dns2:94.255.29.222;sess_id:1700:DC:38:E1:F6:D4:52;
Jan 1 00:00:19 resident_ppp_handler[386]: Set default type: ipv4
Jan 1 00:00:19 resident_ppp_handler[386]: ++++++++++ line 1665
Jan 1 00:00:19 resident_ppp_handler[386]: ++++++++++ line 1673
Jan 1 00:00:19 resident_ppp_handler[386]: l2:eth1, l3:eth1_3, tun:||
Jan 1 00:00:19 resident_ppp_handler[386]: ++++++++++ line 1828
Jan 1 00:00:19 resident[386]: ppp_is_up on eth1_3
Jan 1 00:00:19 DMS_ROUTE_SUCCESS[386]: ADD default via (null) dev ppp0 metr 50 table 254 (ppp_is_up)
Jan 1 00:00:19 DMS_ROUTE_SUCCESS[386]: ADD default via (null) dev ppp0 metr 50 table 253 (ppp_is_up)
Jan 1 00:00:19 update_wan_firewall[386]: firewall enable
Jan 1 00:00:19 triggerPingRespond[386]: OK
Jan 1 00:00:19 update_ripd[386]: update rip
Jan 1 00:00:19 dms_redirect_state_output[386]: is_active = yes is_factory = no is_con_up_v4 = yes is_con_up_v6 = no is_flashing = no is_configuring = no
Jan 1 00:00:19 dms_redirect_state_output[386]: eth: on dsl: off usb: off configuring off default port: ethernet
Jan 1 00:00:19 dms_redirect_cfg_output[386]: enable = yes, cable = yes, connections = yes, factory = yes, flashing = yes
Jan 1 00:00:20 update_ntpclient[386]: starts
Jan 1 00:00:20 update_ntpclient[386]: server string: ntpd -p pool.ntp.org&
Jan 1 03:00:20 dms_redirect_state_output[386]: is_active = no is_factory = no is_con_up_v4 = yes is_con_up_v6 = no is_flashing = no is_configuring = no
Jan 1 03:00:20 dms_redirect_state_output[386]: eth: on dsl: off usb: off configuring off default port: ethernet
Jan 1 03:00:20 dms_redirect_cfg_output[386]: enable = yes, cable = yes, connections = yes, factory = yes, flashing = yes
Jan 1 03:00:20 restart_udpxy[386]: udpxy has restarted
Jan 1 03:00:20 stop_udpxy[386]: udpxy has stoped
Jan 1 03:00:21 restart_udpxy[386]: udpxy has restarted wan =ppp0
Jan 1 03:00:21 resident[386]: stop igmpx
Jan 1 03:00:21 start_udpxy[386]: udpxy has started on *.^Xl*.^Xt*.m,*.l^P*. 8.D.*.*p
Jan 1 03:00:21 udpxy[447]: udpxy 1.0-23.9 (prod) standard [Linux 2.6.30.9 rlx] is starting
Jan 1 03:00:21 start_udpxy[386]: udpxy has started on ppp0 with pid 445
Jan 1 03:00:22 recheck_dnsmasq[386]: MD5 sum of /tmp/dnsmasq.conf before and after matching, not restarting DNSMASQ
Jan 1 03:00:22 restart_udpxy[386]: udpxy has restarted
Jan 1 03:00:22 stop_udpxy[386]: udpxy has stoped
Jan 1 03:00:22 udpxy[447]: udpxy 1.0-23.9 (prod) standard [Linux 2.6.30.9 rlx] is exiting with rc=[0]
Jan 1 03:00:23 restart_udpxy[386]: udpxy has restarted wan =ppp0
Jan 1 03:00:23 resident[386]: stop igmpx
Jan 1 03:00:23 start_udpxy[386]: udpxy has started on *.^Xl*.^Xt*.m,*.l^P*. 8.Ft*.*p
Jan 1 03:00:23 udpxy[468]: udpxy 1.0-23.9 (prod) standard [Linux 2.6.30.9 rlx] is starting
Jan 1 03:00:23 start_udpxy[386]: udpxy has started on ppp0 with pid 466
Jan 1 03:00:23 nvram[37]: client accepted
Jan 1 03:00:23 nvram[37]: client accepted
Oct 7 02:01:01 kernel: wlan0: A wireless client is associated - 74:04:2B:97:F2:CD
Oct 7 02:01:01 kernel: wlan0: WPA2-AES PSK authentication in progress...
Oct 7 02:01:01 kernel: wlan0: A wireless client is associated - 74:04:2B:97:F2:CD
Oct 7 02:01:01 kernel: wlan0: Open and authenticated
Oct 7 02:01:17 pppd[293]: System time change detected.
Oct 7 02:01:32 kernel: wlan0: A wireless client is associated - B8:76:3F:0F:F5:C1
Oct 7 02:01:32 kernel: wlan0: WPA2-AES PSK authentication in progress...
Oct 7 02:01:32 kernel: wlan0: A wireless client is associated - B8:76:3F:0F:F5:C1
Oct 7 02:01:32 kernel: wlan0: Open and authenticated
Oct 7 02:01:37 kernel: icmpv6_send: no reply to icmp error
Oct 7 02:01:37 kernel: icmpv6_send: no reply to icmp error
Oct 7 02:01:40 morda[479]: user admin is logged in with administrator privileges to the ip ::ffff:192.168.1.13
Oct 7 02:01:46 kernel: icmpv6_send: no reply to icmp error