Есть 104 и 1104 настроеные в режиме hot-line по протоколу g729.
если поставить set coding off, то (как я понимаю) передача DTMF идет в голосе, и возникают проблемы с потерей цифр.
При включении set coding x on oob 104 передает сигналы (в логе их видно), то 1104 их не воспринимает.
Как заставить 1104 принимать сигналы по h245?
1104:
usr/config$sysconf -print
System information
Gateway Service: 2
Inter-Digit time out : 5
End of Dial : [ # ] button
Port status:
port1: Enabled
port2: Enabled
port3: Enabled
port4: Enabled
DTMF selection : H.245 Alphanumeric
Line seizure mode: None
2nddial: Off
Dial Rule
outgoing call:(Call from PSTN)
filter: [] drop: [] insert: [].
incoming call:(Call from IP)
filter: [] drop: [] insert: [].
PIN prompt: 0
set1: 1111
set2: 2222
set3: 3333
set4: 4444
Ring Detect Method: 1
Ring before Answer: 3
FAX redundancy depth: 0
Caller ID Detect: disable
usr/config$ h323 -print
H.323 stack relate information
RAS mode : Peer-to-Peer
Registration mode : Gateway
Q931 port : 1720
RAS port : 1024
RTP port : 16384
Default Gateway : x
Allocated port range :
start port : 1024
end port : 65535
Response timeOut : 5
Connect timeOut : 200
usr/config$ voice -print
Voice codec setting relate information
Sending packet size :
G.729A : 40 ms
G.729A : 40 ms
G.729A : 40 ms
G.729A : 40 ms
G.729 : 40 ms
Priority order codec :
g729a g729a g729a g729a g729
Volume levels :
voice volume : 40
input gain : 32
dtmf volume : 24
Sound compress & CNG :
Echo canceller : On On On On
JitterBuffer Min Delay : 90
JitterBuffer Max Delay : 150
usr/config$ support -print
Special Voice function support manipulation
T.38(FAX) support : Disabled.
T.38(FAX) ECM : Enabled.
FastStart support : Enabled.
Tunnelled H.245 support : Enabled.
H.245 message after FastStart : Enabled.
на 104:
Configuration for coding profile id 5:
Tx Coding = G.729AB
Rx Coding = G.729AB
Coding profile for voice
Tx VIF size = 160 (bits)
Rx VIF size = 160 (bits)
VAD = Enabled
VAD threshold = 0 (dB) (relative to ref level of -30dBm)
Playout nominal delay = 60 (msec)
Playout maximum delay = 120 (msec)
Playout minimum delay = 0 (msec)
Adaptive Playout = Adjust immediately
Rate = 14400
DTMF Relay = out-of-band:report to host, don't pass as voice
Tone detect = Enabled
Call Progress Tone detect = Disabled
V.18 Tone detect = Disabled
SS7 COT Tone detect = Disabled
SF Sig Tone detect = Disabled
EC = Enabled
EC NL = Enabled
EC NL Sens = 0
EC Tail = 8 (msec)
EC Refresh = Update
EC Coeffs = Normal
EC Auto Update = Disabled
EC Auto Search = Disabled
EC Search Freeze = Disabled
Modem TX level = -13 (dB)
Modem CD threshold = 0
Modem no activity timeout = 20 (sec)
Caller ID Support = Disabled
Resampling = Disabled
EC Config = Invalid (0)
NLP Confort Noise = 0
SID Retx Rate = 0
Encapsulation = RTP
Tx ssrc = 0
Tx start timestamp = 0
Rx ssrc = 0
Rx start timestamp = 0
Tx digit payload = 0
Rx digit payload = 0
Digit repetitions = 3
Secondary Decoder = Disabled
и еще вопрос, в 104 можно настроить чтобы он лучще воспринимал DTMF коды?
ПОМОГИ ПОЖАЛУЙСТА, КТО МОЖЕТ, ОЧЕНЬ НУЖНО СРОЧНО РАЗОБРАТЬСЯ!!!